搜索结果: 1-12 共查到“有色金属及其合金 Mg-Al”相关记录12条 . 查询时间(0.125 秒)
本发明涉及镁合金表面处理领域,具体地说是一种镁合金表面原位生长Mg-Al水滑石膜的成膜溶液,以及使用所述溶液在镁合金表面制备Mg-Al水滑石膜的方法。该成膜溶液包括前处理液和后处理液,前处理溶液是在饱和碳酸溶液中滴加含Al的碱性溶液所得,含Al的碱性溶液是将纯铝板放在室温至90℃的碱性溶液中溶解至饱和所得；后处理溶液是在前处理液基础上,用碱性溶液调节pH值所得；镁合金为含铝量低或不含铝的镁合金。采...
Selection of heat treatment condition of the Mg-Al-Zn alloys
Heat treatment Magnesium alloys Mechanical properties
2009/12/14
Purpose: Main aim of this paper are results of the optimization of heat treatment conditions, which are temperature and heating time during solution heat treatment or ageing as well the cooling rate a...
Structure and properties of alloys of the Mg-Al-Zn system
Mechanical properties Magnesium alloys Tensile test at elevated temperatures
2009/12/14
Purpose: In the following paper there have been the structure and complex of mechanical properties of magnesium alloys presented which requires very often knowledge of elastic-plastic properties at el...
The influence of the heat treatment on the microstructure and properties of Mg-Al-Zn based alloys
Heat Treatment Metallography Magnesium alloys
2009/12/3
Purpose: In the following paper there have been the structure and properties of the MCMgAl12Zn1, MCMgAl9Zn1, MCMgAl6Zn1, MCMgAl3Zn1 magnesium cast alloy as-cast state and after a heat treatment presen...
Characteristic of Mg-Al-Zn alloys after laser treatment
Laser alloying Magnesium alloy High Power Diode Laser (HPDL)
2009/12/2
Purpose: The structure and the properties of casting magnesium alloy EN-MCMgAl3Zn1, EN-MCMgAl6Zn1,
EN-MCMgAl9Zn1 and EN-MCMgAl12Zn1 after laser surface treatment are presented in this paper. The aim ...
Purpose: The aim of the present work is to study the influence of temperature on tensile properties of the magnesium
alloy AJ50, and to discuss possible hardening and softening mechanisms and therma...
铸造Mg-Al-Zn合金的成分、相组成与凝固路径的关系
Mg-Al-Zn合金 相平衡热力学 显微组织
2009/11/30
采用SEM, EDS和XRD研究了几种Mg-Al-Zn合金的成分、相组成与凝固路径的关系. 结果表明, Mg-Al-Zn合金的相组成与Zn/Al质量比有关；随着Zn/Al比值的增加, 第二相γ-Mg17Al12的数量减少, 逐渐被Φ-Mg21(Zn, Al)17 取代, 直至完全消失. 通过搜集合金中可能存在的各相的热力学模型, 运用Pandat热力学计算软件平台, 计算并比较了平衡和非平衡(Sc...
运用固体与分子经验电子理论(EET)的计算结果分别建立Al-Si、Mg-Al两种合金熔体的剩余化学键的局域价电子结构基本单元即残余键结构模型，从压力对熔体结构作用的层面，分析热力学平衡相图中最大固溶点和共晶点发生偏移的本质原因，并指出压力作用下热力学平衡相图的变化是合金熔体微观结构信息变化的宏观反映。结果表明：压力作用抑制了合金熔体中Si-Si、Al12残余键结构的扩散速率，使其不容易“捕捉”到周...
Formation of Al3Ti/Mg composite by powder metallurgy of Mg–Al–Ti system
metal-matrix composites (MMCs) Mg–Al–Ti system powder metallurgy intermetallics
2008/9/1
An in situ titanium trialuminide (Al3Ti)-particle-reinforced magnesium matrix composite has
been successfully fabricated by the powder metallurgy of a Mg–Al–Ti system. The reaction
processes and for...
应用透射电镜(TEM)研究了时效AZ91 Mg-Al合金中三种形态的γ-Mg17Al12析出相(bcc)的多重位向关系及析出相颗粒间的{112}γ伪孪晶关系.这三种板条状、六棱柱状或短棒状的析出相分别与Mg基体(hcp)保持Burgers,Crawley和Porter位向关系;在同种析出相颗粒之间或异种颗粒之间能形成不具有孪晶结构特征的{112}γ伪孪晶关系.从晶体学角度解释了这种多重位向关系及伪...
应用透射电镜研究了时效AZ91Mg-Al合金连续析出相的显微组织形态及晶体学特征.发现四种不同形态和晶体学特征的β-(Mg17Al12)析出相,其中占绝大多数的是板条状析出相.沿基面(0001)α析出的板条析出相与基体保持Burgers位向关系,生长方向为[7,2, ,0];其晶体学特征与由不变线应变原理预测的完全一致.第二类析出相是以其轴线与基面垂直的六棱柱体,六个棱柱面都是{ 100}αⅣ{ ...